Datamax O'Neil M-4308 Návod k obsluze Strana 37
- Strana / 100
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 4 – Menu System 31
FORMAT
MODULE *
Selects from a list of modules available for formatting by the printer; see Section
5.10, File Handling Messages. Choosing FORMAT MODULE will erase existing data
in the selected module
DELETE FILE * Selects from the list of available files for deleting; see Section 5.10, File Handling
Messages.
COPY FILE * Selects from the list of available files for copying, prompting you for the
destination module before execution; see Section 5.10, File Handling Messages.
UNPROTECT
MODULE *
Selects from the list of available modules to unprotect, and then prompting you
regarding the outcome of the attempt; see Section 5.10, File Handling Messages.
PRESENT SENSOR Controls the "on-demand" dispensing of labels , where:
MODE Sets the detection method and response of the printer:
AUTO Is the default setting. Automatically detects, enables the Present Sensor (or Peel
and Present mechanism) and sets the label stop location; if not detected, the
operation will be ignored.
ENABLED Enables the Present Sensor (or Peel and Present mechanism) and sets the label
stop location; if not detected, a fault will be generated.
DISABLED Disables the option.
RETRACT DELAY
*
Programs a time delay for the retraction of the next label in the print process,
where:
(1 - 255 x 10 mS)
070
Is the range, times 10 milliseconds; and,
Seventy (times ten) is the default setting.
CUTTER Controls the Cutter operation, where:
MODE Sets the detection method and response of the printer:
AUTO Is the default setting, where the presence of the cutter option is automatically
sensed. If detected, the cutter is enabled; otherwise, it will be ignored.
ENABLED Enables the cutter. If the cutter is not detected, a fault will be generated.
DISABLED Disables the cutter.
CUT BEHIND Allows a queue of small labels to accumulate before cutting is performed to
increase throughput.
(1) This mode can be used without a cutter to allow the presentation of
an extra label with retraction upon the next job or feed operation.
(2) After a fault or unknown label position, the leading edge will be cut
to ensure no extra material exists at the beginning of the first label;
otherwise, the cutter will only cut when necessary.
(0 – 2)
0
Zero, one, or two are the number of labels to queue before cutting; and
Is the default setting.
RFID Controls the programming and verification of RFID tags, where:
If not installed (or detected), this selection will result in a DISABLED
message.
RFID MODULE Sets the mode of RFID operation, where:
DISABLED Disables the option.
HF Selects the High Frequency (13.56 MHz) RFID option.
UHF MULTI-
PROTOCOL
Selects the Ultra High Frequency (868-956 MHz) RFID option.
RFID POSITION* Sets the RFID inlay location.
(1.10 - 4.00 IN.)
1.10
This location is referenced from the leading edge of the label or tag, as it moves
forward through the printer.
Is the default setting.
- Operator’s Manual 1
- Copyright Information 3
- Limitation of Liability 3
- 1 Getting Started 5
- 2 Printer Setup 5
- 3 Printer Operation 5
- 4 Menu System 5
- Additional Requirements 7
- Chapter 2 - Printer Setup 3 9
- Power Connection 9
- Chapter 2 - Printer Setup 4 10
- Interface Connection 10
- Chapter 2 - Printer Setup 5 11
- Chapter 2 - Printer Setup 6 12
- Chapter 2 - Printer Setup 7 13
- ‘Sensor Eye’ Mark 14
- Slide Tab 14
- Ink Side (CSO Ribbon) 15
- Ink Side (CSI Ribbon) 15
- Printhead Latch 15
- Ribbon Take-up Hub 18
- 3.1.1 Lights 19
- 3.1.2 Buttons 20
- Icons & Indicators 21
- Important Notes: 23
- 3.5.1 Quick Calibration 25
- 3.5.2 Empty Calibration 25
- 3.5.3 Standard Calibration 26
- Chapter 4 – Menu System 23 29
- Chapter 4 – Menu System 24 30
- Chapter 4 – Menu System 25 31
- Media Settings 31
- Chapter 4 – Menu System 26 32
- Chapter 4 – Menu System 27 33
- Chapter 4 – Menu System 28 34
- Print Control 34
- Chapter 4 – Menu System 29 35
- Chapter 4 – Menu System 30 36
- Printer Options 36
- (1 - 255 x 10 mS) 37
- (1.10 - 4.00 IN.) 37
- Chapter 4 – Menu System 32 38
- Chapter 4 – Menu System 33 39
- Chapter 4 – Menu System 34 40
- System Settings 40
- Chapter 4 – Menu System 35 41
- Chapter 4 – Menu System 36 42
- Chapter 4 – Menu System 37 43
- Chapter 4 – Menu System 38 44
- Chapter 4 – Menu System 39 45
- Chapter 4 – Menu System 40 46
- Chapter 4 – Menu System 41 47
- Communications 47
- Chapter 4 – Menu System 42 48
- ALTERNATE 49
- CODES 2 49
- Chapter 4 – Menu System 44 50
- Chapter 4 – Menu System 45 51
- Diagnostics 51
- Chapter 4 – Menu System 46 52
- MCL Options 52
- Printhead Assembly 54
- Cotton Swab 54
- Thumbscrew 55
- Printhead Mounting Screw 58
- Darkness Adjustment 59
- Fault Messages: 69
- 72
- Warning Messages: 73
- Mechanical 75
- Printing 75
- GPIO Port Configuration 79
- Printer Setup Mode 81
- Menu Item 82
- Menu Items and Values 83
- Label 1 Label 2 87
- Label Alignment = YES 88
- Label Alignment = AUTO 89
- Label Alignment = NO 89
- Calibration Mode 92
Související produkty a manuály pro Tiskárny štítků Datamax O'Neil M-4308
(36 stránky)LG XB12-D0U podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Nie LG XB12-D0U.
Dostarczamy 1 pdf podręczników LG XB12-D0U do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce