Datamax-oneil S-Class DTPL Programmer’s Manual Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Tiskárny Datamax-oneil S-Class DTPL Programmer’s Manual. Datamax-O'Neil S-Class DTPL Programmer’s Manual User Manual [it] Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - DTPL Pro

DTPL Programmer’s Manual

Strany 2

DTPL Programmer’s Manual 4 Font Size Command <Fx> This command sets the font size. The defaults is F3. x= 1 for Font1 characters (5x7) 2 for

Strany 3

DTPL Programmer’s Manual 5 DTPL Status Commands 3.0 Introduction The status-enabled function must be set to activate these commands. Command Fo

Strany 4

DTPL Programmer’s Manual 6 Command Format Description No Status <S5> or <s5> Disables the transmission of all status information, exc

Strany 5 - Contents

DTPL Programmer’s Manual 7 DTPL File Commands 4.0 Introduction The printer supports three modes of file storage: Resident: Files are stored

Strany 6

DTPL Programmer’s Manual 8

Strany 7 - Introduction

DTPL Programmer’s Manual 9 DTPL Print Commands 5.0 Introduction The following table lists the printer’s various print commands. Command Format

Strany 8 - 1.4 Graphics

DTPL Programmer’s Manual 10

Strany 9 - DTPL Command Sequences

DTPL Programmer’s Manual 11 DTPL Special Commands 6.0 Introduction The following commands are to be transmitted independently (without the <

Strany 10 - DTPL Programmer’s Manual 4

DTPL Programmer’s Manual 12

Strany 11 - DTPL Status Commands

DTPL Programmer’s Manual 13 DTPL Downloading Commands 7.0 Downloading Commands Logos can originate in one of two manners. They can be permanentl

Strany 13 - DTPL File Commands

DTPL Programmer’s Manual 14 The above routine should be repeated for each line of logo data. For the remaining lines, a CR should be used in place of

Strany 14 - DTPL Programmer’s Manual 8

DTPL Programmer’s Manual 15 DTPL TEXT LOGO (MACRO) SUPPLEMENT The printer can store a string of DTPL commands (a macro) in memory as if they were a

Strany 15 - DTPL Print Commands

DTPL Programmer’s Manual 16

Strany 16 - DTPL Programmer’s Manual 10

DTPL Programmer’s Manual 17 Barcodes 8.0 Barcodes UPC UPC (version A) is a numeric only code which contains a left hand border character, 6 le

Strany 17 - DTPL Special Commands

DTPL Programmer’s Manual 18 A typical ladder orientation bar code with interpretation and a default width of 4 would be sent as follows. "<R

Strany 18 - DTPL Programmer’s Manual 12

DTPL Programmer’s Manual 19 USS-CODABAR USS-CODABAR is a numeric bar code with 6 special characters (-$:/.+) and 4 start/stop characters (A,B,C,D).

Strany 19 - DTPL Downloading Commands

DTPL Programmer’s Manual 20

Strany 20 - DTPL Programmer’s Manual 14

DTPL Programmer’s Manual A-1 Appendix A ASCII Control Chart Char Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Ctrl @ NUL 0

Strany 21 - DTPL Programmer’s Manual 15

DTPL Programmer’s Manual A-2 ASCII Control Chart (concluded) Char Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Ç 128 80 á 160 A0

Strany 22 - DTPL Programmer’s Manual 16

Information in this manual is subject to change without notice and does not represent a commitment on the part of Datamax-O’Neil Corporation.

Strany 24 - DTPL Programmer’s Manual 18

i Contents Introduction 1.0 Manual Overview...

Strany 26 - DTPL Programmer’s Manual 20

DTPL Programmer’s Manual 1 Introduction 1.0 Manual Overview This manual is designed for users who wish to create their own label production soft

Strany 27 - Appendix A

DTPL Programmer’s Manual 2 1.3 Bar Codes The following highlights some key points on printing barcodes:  All available barcodes (Code 39, Interle

Strany 28

DTPL Programmer’s Manual 3 DTPL Command Sequences 2.0 Introduction The printer can accept a wide variety of commands to control the printing of d

Komentáře k této Příručce

Žádné komentáře