Datamax O'Neil M-4308 Návod k obsluze Strana 38
- Strana / 100
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 4 – Menu System 32
HF SETTINGS * Sets HF tag parameters, as follows:
TAG TYPE Sets the tag type:
ISO 15693 (Is the default setting.)
TI
PHILIPS
ST LRI512
ST LRI64
AFI VALUE Application Family Identifier value (00 - FF), where 00 is the default value.
AFI LOCK Application Family Identifier lock (ENABLED / DISABLED), where DISABLED is the
default setting.
DSFID VALUE Data Storage Format Identifier (00 - FF), where 00 is the default value.
DSFID LOCK Data Storage Format Identifier lock (ENABLED / DISABLED), where DISABLED is
the default setting.
EAS VALUE Electronic Article Surveillance value (00 - FF), where 00 is the default value.
AUDIO
INDICATOR
Controls the buzzer (ENABLED / DISABLED), where DISABLED is the default
setting.
ERASE ON
FAULT
Erases the tag when errors are detected (ENABLED / DISABLED), where DISABLED
is the default setting.
UHF SETTINGS * Sets UHF tag parameters, as follows:
TAG TYPE Sets the tag type:
EPC 0
EPC 0+ MATRICS
EPC 0+ IMPINJ
EPC 1
UCODE EPC 1.19
EM 4022/1222
GEN 2 (Is the default setting.)
TAG DATA
SIZE
Sets the tag data size:
96-BIT (Is the default setting.)
64-BIT
POWER
ADJUST
Adjusts the applied power.
KILL CODE Code used to permanently deactivate the device:
B3 B2 B1 B0
00 00 00 00 (Is the default setting.)
ACCESS
CODE
Code used to protect the memory contents:
B3 B2 B1 B0
00 00 00 00 (Is the default setting.)
GEN 2 LOCK
ACTION
Sets the lock level (NONE, PERMALOCK, PWD-READ/WRITE, BOTH), where NONE is
the default setting.
LOCK AFTER
WRITE *
Locks the tag after programming.
ENABLED The tag will be locked.
DISABLED No locking occurs (default setting).
RETRY
ATTEMPTS *
Sets the number of retry attempts, where:
(0 - 9)
3
Zero to nine are the number of retries; and,
Is the default setting.
PERFORM
CALIBRATION *
Allows the printer to establish the tag to transducer distance setting and nominal
RFID power requirements.
YES Initiates the process. The CALIBRATING RFID message will appear as the printer
feeds media to begin scanning for the RFID tag location. Once the location is
established, power calibration begins. Upon completion, the media will be retracted
to the TOF position; the calibrated position and power results (along with a brief
SUCCESS or FAILURE message) will be displayed; and, the printer’s database will
be updated with the new calibration parameters.
NO Terminates the process.
- Operator’s Manual 1
- Copyright Information 3
- Limitation of Liability 3
- 1 Getting Started 5
- 2 Printer Setup 5
- 3 Printer Operation 5
- 4 Menu System 5
- Additional Requirements 7
- Chapter 2 - Printer Setup 3 9
- Power Connection 9
- Chapter 2 - Printer Setup 4 10
- Interface Connection 10
- Chapter 2 - Printer Setup 5 11
- Chapter 2 - Printer Setup 6 12
- Chapter 2 - Printer Setup 7 13
- ‘Sensor Eye’ Mark 14
- Slide Tab 14
- Ink Side (CSO Ribbon) 15
- Ink Side (CSI Ribbon) 15
- Printhead Latch 15
- Ribbon Take-up Hub 18
- 3.1.1 Lights 19
- 3.1.2 Buttons 20
- Icons & Indicators 21
- Important Notes: 23
- 3.5.1 Quick Calibration 25
- 3.5.2 Empty Calibration 25
- 3.5.3 Standard Calibration 26
- Chapter 4 – Menu System 23 29
- Chapter 4 – Menu System 24 30
- Chapter 4 – Menu System 25 31
- Media Settings 31
- Chapter 4 – Menu System 26 32
- Chapter 4 – Menu System 27 33
- Chapter 4 – Menu System 28 34
- Print Control 34
- Chapter 4 – Menu System 29 35
- Chapter 4 – Menu System 30 36
- Printer Options 36
- (1 - 255 x 10 mS) 37
- (1.10 - 4.00 IN.) 37
- Chapter 4 – Menu System 32 38
- Chapter 4 – Menu System 33 39
- Chapter 4 – Menu System 34 40
- System Settings 40
- Chapter 4 – Menu System 35 41
- Chapter 4 – Menu System 36 42
- Chapter 4 – Menu System 37 43
- Chapter 4 – Menu System 38 44
- Chapter 4 – Menu System 39 45
- Chapter 4 – Menu System 40 46
- Chapter 4 – Menu System 41 47
- Communications 47
- Chapter 4 – Menu System 42 48
- ALTERNATE 49
- CODES 2 49
- Chapter 4 – Menu System 44 50
- Chapter 4 – Menu System 45 51
- Diagnostics 51
- Chapter 4 – Menu System 46 52
- MCL Options 52
- Printhead Assembly 54
- Cotton Swab 54
- Thumbscrew 55
- Printhead Mounting Screw 58
- Darkness Adjustment 59
- Fault Messages: 69
- 72
- Warning Messages: 73
- Mechanical 75
- Printing 75
- GPIO Port Configuration 79
- Printer Setup Mode 81
- Menu Item 82
- Menu Items and Values 83
- Label 1 Label 2 87
- Label Alignment = YES 88
- Label Alignment = AUTO 89
- Label Alignment = NO 89
- Calibration Mode 92
Související produkty a manuály pro Tiskárny štítků Datamax O'Neil M-4308
(36 stránky)LG XB12-D0U podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Nie LG XB12-D0U.
Dostarczamy 1 pdf podręczników LG XB12-D0U do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce