Datamax-oneil DPL Programmer’s Manual Uživatelský manuál Strana 71
- Strana / 296
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Extended System-Level Command Functions
63
(EQ) Start of Print – This command defines the type of signal input required to
control the Start of Print (SOP) process:
Value Units Start of Print Interpretation
3 Active Low
SOP signal must go low for at least 50 milliseconds to initiate
printing.
4 Active High
SOP signal must go high for at least 50 milliseconds to
initiate printing.
(ES) ESC Sequences – This command allows data containing invalid ESC control
code sequences to be processed (helpful because some systems send a “banner” to
the printer). When set to “Disabled,” ESC sequences are ignored and the data is
processed. Bitmapped font downloads are disabled in this mode.
(EV) Empty Sensor Level – This command sets threshold value for the “Empty”
media sensor parameter.
(FA) Format Attribute – See the “An” command for details (Label Formatting
Command Functions).
(FB) Scalable Font Bolding – This command sets a bolding factor to fine tune
scalable fonts, where one causes the least amount of bolding and thirty-six the most
(default value is 8).
(FE) Font Emulation –This command allows font substitution for all internal fonts,
allowing a new default font to be defined without changing the host DPL data
streams. Selecting a default font that supports a desired character set could match
with third party software to print native characters without modifying the PC drivers.
In other words, match the PC font with the Printer Font then no interpretation would
be required by driver or printer. Depending on host drivers, the user may have to
disable Symbol Set commands and modify the Default Symbol set.
- Programmer’s Manual 1
- Contents 3
- 1 Overview 9
- General Conventions 10
- Special Instructions 10
- Typical Data Flow Sequence 11
- ) commands can be changed at 13
- Overview 14
- 15
- Alternate Control Code Modes 16
- Immediate Command Functions 17
- SOH B Toggle Pause 19
- SOH C Stop/Cancel 20
- SOH D SOH Shutdown 20
- SOH F Send Status Byte 21
- STX A Set Time and Date 23
- STX I Input Image Data 27
- STX o Cycle Cutter 30
- STX P Set Hex Dump Mode 31
- STX p Controlled Pause 31
- STX Q Clear All Modules 31
- STX q Clear Module 32
- STX R Ribbon Saver Control 32
- STX S Set Feed Speed 33
- STX T Print Quality Label 33
- STX X Set Default Module 37
- STX z Pack Module 40
- Extended System-Level 41
- STX Kb Backfeed Time Delay 44
- STX KC Get Configuration 45
- STX Kc Configuration Set 48
- STX KE Character Encoding 101
- STX KH Dot Check 104
- STX KI GPIO Input 106
- STX Kn NIC Reset 106
- STX KO GPIO Output 107
- STX Kp Module Protection 108
- Label Formatting 119
- Command Functions 119
- A Set Format Attribute 120
- B Bar Code Magnification 121
- C Set Column Offset Amount 121
- H Enter Heat Setting 124
- J Justification 125
- M Select Mirror Mode 125
- P Set Print Speed 126
- of .37 128
- S Set Feed Speed 130
- Embedding 135
- STX D Print adjusted date 137
- STX T Print Time and Date 138
- Introduction 141
- )s###W Font Descriptor 142
- *c###E Character Code 142
- 8 Generating Label Formats 143
- Generating Records 144
- The Structure of a Record 144
- Record Structure Types 148
- Fill Patterns 155
- Generating Label Formats 158
- Appendix A 161
- 10K OHM 1/4 WATT 163
- Appendix B – Sample Programs 164
- Appendix C 173
- Appendix C – Available Fonts 176
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- Appendix E – Symbol Sets 192
- Appendix F 193
- Appendix G 199
- Barcode I 204
- Barcode S 208
- Barcode T 208
- Barcode U 211
- Barcode z 212
- Barcode Z 213
- Barcode W1c 215
- Barcode W1C 216
- Barcode W1D 220
- Barcode W1f 225
- Barcode W1F 225
- Barcode W1G 226
- Barcode W1I 228
- Barcode W1J 229
- Barcode W1k 231
- Barcode W1L 233
- Barcode W1M 235
- Barcode W1m 235
- Barcode W1N 235
- (IMB) 236
- 34 567890 123 4567 238
- Barcode W1t 239
- Barcode W1Y 240
- Barcode W1Z 242
- Appendix H 245
- Appendix I 247
- Appendix J 251
- • Pins 1 – 2 = +5VDC; 252
- • Pins 2 – 3 = +24VDC; or 252
- • None = A common external 252
- Appendix K 253
- Appendix L 255
- Appendix M 257
- Appendix N 259
- Appendix N – Image Loading 260
- Appendix O 261
- Appendix P 263
- Appendix Q 273
- Appendix R 275
- Appendix R – Line Mode 276
- Appendix S 279
- Appendix S – RFID Overview 280
- Field Valid Inputs Meaning 283
- Appendix T 285
- Appendix U 291
- Glossary 293
Související produkty a manuály pro Tiskárny Datamax-oneil DPL Programmer’s Manual
(8 stránky)LG XB12-D0U podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Nie LG XB12-D0U.
Dostarczamy 1 pdf podręczników LG XB12-D0U do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce